APACHE POINT OBSERVATORY SDSS 2.5M OBSERVING LOG Tuesday April 20, 2010 (MJD 55307) ---=== OBSERVING TEAM ===--- Steph Snedden Dmitry Bizyaev ---=== OBSERVING PLAN ===--- BOSS Science ---=== OBSERVING SUMMARY ===--- Clouds in the first part of the night. Opened in the evening, then closed because of clouds, then opened again. BOSS plates exposed: 3818 (c. 10) not done 3969 (c. 14) done 3871 (c. 16) done 3941 (c. 17) not done Kyle's test is completed (see log) ---=== OBSERVING LOG ===--- Afternoon --------- 00:40Z ventilation started cart. 10 mounted collimation chechek Night: ------ We have radar returns approaching, but we fill there will be some an hour to observe, so we decided to open. 01:40Z enclosure off 02:00Z gotoField with cart. 10 plate 3818 GSPGTF seeing ~ 0.9" - 1.1" 5 01:08 b1-00113885 10 3818 arc Lef 4.8 32095 32663 32661 HART 6 01:09 b1-00113886 10 3818 arc Rig 4.8 32095 32663 32661 HART 7 01:17 b1-00113887 10 3818 arc Lef 4.8 30710 31277 31277 HART 8 01:19 b1-00113888 10 3818 arc Rig 4.8 30710 31277 31277 HART 9 02:11 b1-00113889 10 3818 arc Lef 4.8 30710 31277 31277 HART 10 02:13 b1-00113890 10 3818 arc Rig 4.8 30710 31277 31277 HART 11 02:19 b1-00113891 10 3818 arc Lef 4.8 32219 32785 32786 HART 12 02:21 b1-00113892 10 3818 arc Rig 4.8 32219 32785 32786 HART 13 02:47 b1-00113893 10 3818 fla Out 30.8 31519 32084 32087 14 02:50 b1-00113894 10 3818 arc Out 4.8 31519 32084 32087 15 02:52 b1-00113895 10 3818 sci Out 900.8 31519 32084 32087 16 03:08 b1-00113896 10 3818 sci Out 900.8 31519 32084 32087 17 03:30 b1-00113897 10 3818 fla Out 30.8 31519 32084 32087 18 03:34 b1-00113898 10 3818 arc Out 4.8 31519 32084 32087 The science exposure 113896 was taken in dense clouds, and has extremely low signal, so we declareed it as "bad". 03:55Z clouds are thickening very much, we barely see the moonlit. We managed to close because no any useful signal is being collected. 04:45Z sky is still cloudy. Kyle called and asked about a 10-min test. We can do it waiting for the clear sky: 1. move pistons by 20,000 counts in the direction that allows the largest range of motion 2. sop hartmann 3. run_collimate and perform adjustments to collimator pistons as suggested 4. sop hartmann 5. perform adjustments if needed - hopefully the routine has converged on the best focus 6. move pistons by 5000 counts in the opposite direction to #1 7. sop hartmann 8. run_collimate and perform adjustments to collimator pistons as suggested 9. sop hartmann --- Test. before this test, we adjust focus for the best collimation: ==> Collimate-55307-b1-00113899.log <== COLLIMATE: RMS across CCD = 0.21 pix COLLIMATE: COLLIMATE: Mean offset = 0.20 pix COLLIMATE: COLLIMATE: Camera b1 appears to be OUT-OF-FOCUS (|mean| > 0.15 pix) COLLIMATE: Predict blue camera ring movement of -4.5 degrees for spectro-1 COLLIMATE: (if red is already in focus) ==> Collimate-55307-b2-00113899.log <== COLLIMATE: RMS across CCD = 0.10 pix COLLIMATE: COLLIMATE: Mean offset = 0.79 pix COLLIMATE: COLLIMATE: Camera b2 appears to be OUT-OF-FOCUS (|mean| > 0.15 pix) COLLIMATE: Predict blue camera ring movement of -17.6 degrees for spectro-2 COLLIMATE: (if red is already in focus) ==> Collimate-55307-r1-00113899.log <== COLLIMATE: Mean offset = 0.25 pix COLLIMATE: COLLIMATE: Camera r1 appears to be OUT-OF-FOCUS (|mean| > 0.15 pix) COLLIMATE: Predict (red) piston movement of 1550 steps for spectro-1 COLLIMATE: Issue command: "boss moveColl spec=sp1 a=1550 b=1550 c=1550" COLLIMATE: current motorPosition 31519 32084 32087 COLLIMATE: new expected motorPosition 33069 33634 33637 ==> Collimate-55307-r2-00113899.log <== COLLIMATE: Mean offset = 0.73 pix COLLIMATE: COLLIMATE: Camera r2 appears to be OUT-OF-FOCUS (|mean| > 0.15 pix) COLLIMATE: Predict (red) piston movement of 5074 steps for spectro-2 COLLIMATE: Issue command: "boss moveColl spec=sp2 a=5074 b=5074 c=5074" COLLIMATE: current motorPosition 10188 9567 11436 COLLIMATE: new expected motorPosition 15262 14641 16510 Collimators moved correspondingly ==> Collimate-55307-b1-00113901.log <== COLLIMATE: RMS across CCD = 0.21 pix COLLIMATE: COLLIMATE: Mean offset = -0.05 pix COLLIMATE: COLLIMATE: Camera b1 appears to be IN-FOCUS (|mean| < 0.15 pix) COLLIMATE: Predict blue camera ring movement of 1.1 degrees for spectro-1 COLLIMATE: (if red is already in focus) ==> Collimate-55307-b2-00113901.log <== COLLIMATE: RMS across CCD = 0.08 pix COLLIMATE: COLLIMATE: Mean offset = 0.00 pix COLLIMATE: COLLIMATE: Camera b2 appears to be IN-FOCUS (|mean| < 0.15 pix) COLLIMATE: Predict blue camera ring movement of -0.0 degrees for spectro-2 COLLIMATE: (if red is already in focus) ==> Collimate-55307-r1-00113901.log <== COLLIMATE: Mean offset = 0.00 pix COLLIMATE: COLLIMATE: Camera r1 appears to be IN-FOCUS (|mean| < 0.15 pix) COLLIMATE: Predict (red) piston movement of 0 steps for spectro-1 COLLIMATE: Issue command: "boss moveColl spec=sp1 a=0 b=0 c=0" COLLIMATE: current motorPosition 33069 33633 33638 COLLIMATE: new expected motorPosition 33069 33633 33638 ==> Collimate-55307-r2-00113901.log <== COLLIMATE: Mean offset = -0.01 pix COLLIMATE: COLLIMATE: Camera r2 appears to be IN-FOCUS (|mean| < 0.15 pix) COLLIMATE: Predict (red) piston movement of -92 steps for spectro-2 COLLIMATE: Issue command: "boss moveColl spec=sp2 a=-92 b=-92 c=-92" COLLIMATE: current motorPosition 15261 14642 16506 COLLIMATE: new expected motorPosition 15169 14550 16414 i.e. we're perfectly there. Then steps: 1. boss moveColl spec=sp1 a=-20000 b=-20000 c=-20000 moves ok boss moveColl spec=sp2 a=-20000 b=-20000 c=-20000 recoils back after ~ 13000, i.e. it hits the limuit. So, we return it nback and go 20000 in other direction. boss moveColl spec=sp1 a=20000 b=20000 c=20000 recoils back after ~ 13000 ticks, i.e. we hit the limit on this spectrograph boss moveColl spec=sp2 a=20000 b=20000 c=20000 moves ok THE TEST IS IMPOSIBLE TO PERFORM WITH ITS ORIGINAL REQUIREMENTS. Any way, we managed to go with 10000 steps rather than 20000. So, we moved pistons +10000 on both, sp1 and sp2 2. 3. ==> Collimate-55307-b1-00113903.log <== COLLIMATE: RMS across CCD = 0.25 pix COLLIMATE: COLLIMATE: Mean offset = -1.59 pix COLLIMATE: COLLIMATE: Camera b1 appears to be OUT-OF-FOCUS (|mean| > 0.15 pix) COLLIMATE: Predict blue camera ring movement of 35.4 degrees for spectro-1 COLLIMATE: (if red is already in focus) ==> Collimate-55307-b2-00113903.log <== COLLIMATE: RMS across CCD = 0.08 pix COLLIMATE: COLLIMATE: Mean offset = -1.59 pix COLLIMATE: COLLIMATE: Camera b2 appears to be OUT-OF-FOCUS (|mean| > 0.15 pix) COLLIMATE: Predict blue camera ring movement of 35.4 degrees for spectro-2 COLLIMATE: (if red is already in focus) ==> Collimate-55307-r1-00113903.log <== COLLIMATE: Mean offset = -1.53 pix COLLIMATE: COLLIMATE: Camera r1 appears to be OUT-OF-FOCUS (|mean| > 0.15 pix) COLLIMATE: Predict (red) piston movement of -9382 steps for spectro-1 COLLIMATE: Issue command: "boss moveColl spec=sp1 a=-9382 b=-9382 c=-9382" COLLIMATE: current motorPosition 43070 43636 43637 COLLIMATE: new expected motorPosition 33688 34254 34255 ==> Collimate-55307-r2-00113903.log <== COLLIMATE: Mean offset = -1.55 pix COLLIMATE: COLLIMATE: Camera r2 appears to be OUT-OF-FOCUS (|mean| > 0.15 pix) COLLIMATE: Predict (red) piston movement of -10748 steps for spectro-2 COLLIMATE: Issue command: "boss moveColl spec=sp2 a=-10748 b=-10748 c=-10748" COLLIMATE: current motorPosition 25169 24549 26414 COLLIMATE: new expected motorPosition 14421 13801 15666 boss moveColl spec=sp1 a=-9382 b=-9382 c=-9382 boss moveColl spec=sp2 a=-10748 b=-10748 c=-10748 4. 5. sop hartmann again ==> Collimate-55307-b1-00113905.log <== COLLIMATE: RMS across CCD = 0.21 pix COLLIMATE: COLLIMATE: Mean offset = -0.15 pix COLLIMATE: COLLIMATE: Camera b1 appears to be IN-FOCUS (|mean| < 0.15 pix) COLLIMATE: Predict blue camera ring movement of 3.3 degrees for spectro-1 COLLIMATE: (if red is already in focus) ==> Collimate-55307-b2-00113905.log <== COLLIMATE: RMS across CCD = 0.08 pix COLLIMATE: COLLIMATE: Mean offset = 0.10 pix COLLIMATE: COLLIMATE: Camera b2 appears to be IN-FOCUS (|mean| < 0.15 pix) COLLIMATE: Predict blue camera ring movement of -2.2 degrees for spectro-2 COLLIMATE: (if red is already in focus) ==> Collimate-55307-r1-00113905.log <== COLLIMATE: Mean offset = -0.11 pix COLLIMATE: COLLIMATE: Camera r1 appears to be IN-FOCUS (|mean| < 0.15 pix) COLLIMATE: Predict (red) piston movement of -652 steps for spectro-1 COLLIMATE: Issue command: "boss moveColl spec=sp1 a=-652 b=-652 c=-652" COLLIMATE: current motorPosition 33688 34253 34257 COLLIMATE: new expected motorPosition 33036 33601 33605 ==> Collimate-55307-r2-00113905.log <== COLLIMATE: Mean offset = 0.09 pix COLLIMATE: COLLIMATE: Camera r2 appears to be IN-FOCUS (|mean| < 0.15 pix) COLLIMATE: Predict (red) piston movement of 599 steps for spectro-2 COLLIMATE: Issue command: "boss moveColl spec=sp2 a=599 b=599 c=599" COLLIMATE: current motorPosition 14421 13801 15665 COLLIMATE: new expected motorPosition 15020 14400 16264 So the suggested move is small. Any way, we do it: boss moveColl spec=sp1 a=-652 b=-652 c=-652 boss moveColl spec=sp2 a=599 b=599 c=599 6. boss moveColl spec=sp1 a=-5000 b=-5000 c=-5000 boss moveColl spec=sp2 a=-5000 b=-5000 c=-5000 7. sop hartmann 8. ==> Collimate-55307-b1-00113907.log <== COLLIMATE: RMS across CCD = 0.23 pix COLLIMATE: COLLIMATE: Mean offset = 0.73 pix COLLIMATE: COLLIMATE: Camera b1 appears to be OUT-OF-FOCUS (|mean| > 0.15 pix) COLLIMATE: Predict blue camera ring movement of -16.2 degrees for spectro-1 COLLIMATE: (if red is already in focus) ==> Collimate-55307-b2-00113907.log <== COLLIMATE: RMS across CCD = 0.10 pix COLLIMATE: COLLIMATE: Mean offset = 0.79 pix COLLIMATE: COLLIMATE: Camera b2 appears to be OUT-OF-FOCUS (|mean| > 0.15 pix) COLLIMATE: Predict blue camera ring movement of -17.6 degrees for spectro-2 COLLIMATE: (if red is already in focus) ==> Collimate-55307-r1-00113907.log <== COLLIMATE: Mean offset = 0.79 pix COLLIMATE: COLLIMATE: Camera r1 appears to be OUT-OF-FOCUS (|mean| > 0.15 pix) COLLIMATE: Predict (red) piston movement of 4854 steps for spectro-1 COLLIMATE: Issue command: "boss moveColl spec=sp1 a=4854 b=4854 c=4854" COLLIMATE: current motorPosition 28036 28600 28606 COLLIMATE: new expected motorPosition 32890 33454 33460 ==> Collimate-55307-r2-00113907.log <== COLLIMATE: Mean offset = 0.74 pix COLLIMATE: COLLIMATE: Camera r2 appears to be OUT-OF-FOCUS (|mean| > 0.15 pix) COLLIMATE: Predict (red) piston movement of 5120 steps for spectro-2 COLLIMATE: Issue command: "boss moveColl spec=sp2 a=5120 b=5120 c=5120" COLLIMATE: current motorPosition 10020 9399 11269 COLLIMATE: new expected motorPosition 15140 14519 16389 boss moveColl spec=sp1 a=4854 b=4854 c=4854 boss moveColl spec=sp2 a=5120 b=5120 c=5120 9. sop hartmann ==> Collimate-55307-b1-00113909.log <== COLLIMATE: RMS across CCD = 0.22 pix COLLIMATE: COLLIMATE: Mean offset = -0.02 pix COLLIMATE: COLLIMATE: Camera b1 appears to be IN-FOCUS (|mean| < 0.15 pix) COLLIMATE: Predict blue camera ring movement of 0.6 degrees for spectro-1 COLLIMATE: (if red is already in focus) ==> Collimate-55307-b2-00113909.log <== COLLIMATE: RMS across CCD = 0.08 pix COLLIMATE: COLLIMATE: Mean offset = 0.00 pix COLLIMATE: COLLIMATE: Camera b2 appears to be IN-FOCUS (|mean| < 0.15 pix) COLLIMATE: Predict blue camera ring movement of -0.0 degrees for spectro-2 COLLIMATE: (if red is already in focus) ==> Collimate-55307-r1-00113909.log <== COLLIMATE: Mean offset = 0.02 pix COLLIMATE: COLLIMATE: Camera r1 appears to be IN-FOCUS (|mean| < 0.15 pix) COLLIMATE: Predict (red) piston movement of 122 steps for spectro-1 COLLIMATE: Issue command: "boss moveColl spec=sp1 a=122 b=122 c=122" COLLIMATE: current motorPosition 32890 33453 33460 COLLIMATE: new expected motorPosition 33012 33575 33582 ==> Collimate-55307-r2-00113909.log <== COLLIMATE: Mean offset = -0.01 pix COLLIMATE: COLLIMATE: Camera r2 appears to be IN-FOCUS (|mean| < 0.15 pix) COLLIMATE: Predict (red) piston movement of -92 steps for spectro-2 COLLIMATE: Issue command: "boss moveColl spec=sp2 a=-92 b=-92 c=-92" COLLIMATE: current motorPosition 15139 14519 16385 COLLIMATE: new expected motorPosition 15047 14427 16293 i.e. the pistons are returned back. No move is really required. Note that lamps were warmed before taking hartmans. ----- 06:57Z done opened. cart 14 plate 3969 is on going to field took 4 attempts because AZ axis was stopped. GSOGTF seeing ~ 1" ==> Collimate-55307-r1-00113911.log <== COLLIMATE: Issue command: "boss moveColl spec=sp1 a=775 b=775 c=775" ==> Collimate-55307-r2-00113911.log <== COLLIMATE: Issue command: "boss moveColl spec=sp2 a=-1245 b=-1245 c=-1245" 31 07:14 b1-00113911 14 3969 arc Lef 4.8 32890 33453 33460 HART 32 07:15 b1-00113912 14 3969 arc Rig 4.8 32890 33453 33460 HART 33 07:20 b1-00113913 14 3969 fla Out 30.8 32890 33453 33460 34 07:22 b1-00113914 14 3969 arc Out 4.8 32890 33453 33460 35 07:28 b1-00113915 14 3969 sci Out 900.8 32890 33453 33460 36 07:44 b1-00113916 14 3969 sci Out 900.8 32890 33453 33460 37 08:01 b1-00113917 14 3969 sci Out 900.8 32890 33453 33460 38 08:17 b1-00113918 14 3969 fla Out 30.8 32890 33453 33460 39 08:20 b1-00113919 14 3969 arc Out 4.8 32890 33453 33460 ------------------------------------------------------------ MJD b1 r1 b2 r2 Texp Sum Plugfile ------------------------------------------------------------ 55307 5.2 8.8 4.7 8.5 900.8 27.2 3969-55303-01 55307 5.9 9.2 6.4 9.2 900.8 30.7 3969-55303-01 55307 6.0 8.1 5.9 8.6 900.8 28.6 3969-55303-01 ------------------------------------------------------------ 17.1 26.1 17.0 26.3 2702.4 --> 86.5 ------------------------------------------------------------ This plate is done. -- 08:22Z cart. 16 plate 3871 is mounted GSOGTF seeing ~ 1.2" 40 08:29 b1-00113920 16 3871 arc Lef 4.8 32890 33453 33460 HART 41 08:30 b1-00113921 16 3871 arc Rig 4.8 32890 33453 33460 HART 42 08:37 b1-00113922 16 3871 arc Lef 4.8 27873 28440 28444 HART 43 08:38 b1-00113923 16 3871 arc Rig 4.8 27873 28440 28444 HART 44 08:42 b1-00113924 16 3871 fla Out 30.8 27873 28440 28444 45 08:45 b1-00113925 16 3871 arc Out 4.8 27873 28440 28444 46 08:51 b1-00113926 16 3871 sci Out 900.8 27873 28440 28444 47 09:08 b1-00113927 16 3871 sci Out 900.8 27873 28440 28444 48 09:24 b1-00113928 16 3871 sci Out 900.8 27873 28440 28444 49 09:41 b1-00113929 16 3871 sci Out 900.8 27873 28440 28444 50 09:57 b1-00113930 16 3871 fla Out 30.8 27873 28440 28444 51 09:59 b1-00113931 16 3871 arc Out 4.8 27873 28440 28444 ------------------------------------------------------------ MJD b1 r1 b2 r2 Texp Sum Plugfile ------------------------------------------------------------ 55307 5.3 9.1 4.9 7.0 900.8 26.3 3871-55303-01 55307 5.5 9.5 5.0 7.0 900.8 27.0 3871-55303-01 55307 5.1 9.2 4.7 6.9 900.8 25.9 3871-55303-01 55307 5.7 10.0 5.4 8.1 900.8 29.2 3871-55303-01 ------------------------------------------------------------ 21.6 37.8 20.0 29.0 3603.2 --> 108.4 ------------------------------------------------------------ This plate is done. -- 10:02Z cart. 17 plate 3941 is mounted GSOGTF seeing ~ 1.0 - 1.2" 52 10:07 b1-00113932 17 3941 arc Lef 4.8 27873 28440 28444 HART 53 10:09 b1-00113933 17 3941 arc Rig 4.8 27873 28440 28444 HART 54 10:13 b1-00113934 17 3941 fla Out 30.8 33257 33823 33827 55 10:16 b1-00113935 17 3941 arc Out 4.8 33257 33823 33827 56 10:21 b1-00113936 17 3941 sci Out 900.8 33257 33823 33827 57 10:38 b1-00113937 17 3941 sci Out 900.8 33257 33823 33827 58 10:54 b1-00113938 17 3941 sci Out 900.8 33257 33823 33827 59 11:11 b1-00113939 17 3941 fla Out 30.8 33257 33823 33827 60 11:14 b1-00113940 17 3941 arc Out 4.8 33257 33823 33827 ------------------------------------------------------------ MJD b1 r1 b2 r2 Texp Sum Plugfile ------------------------------------------------------------ 55307 3.5 7.5 2.9 7.7 900.8 21.6 3941-55303-01 55307 3.4 6.9 2.7 7.1 900.8 20.1 3941-55303-01 55307 2.6 5.3 2.1 6.0 900.8 16.0 3941-55303-01 ------------------------------------------------------------ 9.5 19.7 7.7 20.8 2702.4 --> 57.7 ------------------------------------------------------------ This plate was not finished. 11:20Z enclosude on, ventilation turned off. 11:25Z endNight finished ---=== IMAGING RUN SUMMARY ===--- Run Time Stripe Lambda Last Flavor Comments Start End Begin End Frame ------------------------------------------------------------------------- ---=== IMAGING RUN DETAILS ===--- ---=== SKIPPY RESULTS ===--- Run Frame nFrames stars muErr muRms nuErr nuRms rot az el --------------------------------------------------------------------------- ---=== LTMATCH RESULTS ===--- Run Field nFields alt az nGood rowMean rowSig colMean colSig rot ------------------------------------------------------------------------ ---=== SPECTROSCOPY DATA SUMMARY ===--- Summary Checked (y/n): QA Procedures Done (y/n): UT Exp Time flavor comment (S/N)^2 totals ========================================== b1 r1 b2 r2 ---=== TELESCOPE OFFSETS AND SCALE I ===--- Time Instrument Az Alt Rot Scale pos offset pos offset pos offset ------------------------------------------------------------------------------ ---=== TELESCOPE OFFSETS AND SCALE II ===--- ---=== FOCUS LOG ===--- setmir piston Temp Wind Time Inst scale M1 M2 Foc Az Alt (C) MPH Dir filt fwhm ------------------------------------------------------------------------------ ---=== WEATHER LOG ===--- Wind Time Temp F Dewp F MPH Direction Dust DIMM Sky 00:33Z 50 35 9 274 (W) 1216 - 01:03Z 48 34 6 262 (W) 1280 - 01:37Z 46 34 7 263 (W) 1322 - some clouds 02:10Z 46 35 15 247 (WSW) 1251 - '' 02:41Z 46 35 10 238 (WSW) 1345 - '' 03:11Z 46 35 12 242 (WSW) 1408 - '' 03:41Z 47 35 11 249 (WSW) 1369 - clouds 04:14Z 47 33 13 233 (SW) 1471 - '' 04:45Z 46 33 10 251 (WSW) 1458 - '' 05:15Z 46 32 12 243 (WSW) 1548 - '' 05:49Z 45 32 9 254 (WSW) 1604 - '' 06:22Z 46 32 11 259 (W) 1516 - '' 06:53Z 45 31 14 247 (WSW) 1556 - some clouds 07:23Z 45 31 9 264 (W) 1614 - 07:57Z 44 31 10 259 (W) 1473 - mostly clear 08:30Z 44 32 9 264 (W) 1609 - '' 09:04Z 44 32 11 261 (W) 1554 - '' 09:38Z 44 33 13 263 (W) 1574 - '' 10:12Z 44 33 11 263 (W) 1679 - 10:46Z 44 33 14 265 (W) 1754 - 11:20Z 44 33 13 260 (W) 1715 - ---=== TELESCOPE STATUS ===--- 00:40Z - Began ventilation. Doors and louvers opened, fans on. 01:40Z - Enclosure off. 11:20Z - Enclosure on, doors and louvers closed, fans off. No interlocks bypassed. Status at: 11:26Z Telescope stowed at: 30,121,00 mount Instrument mounted: Cartridge 17 Counterweights at: 245 lbs LN2 autofill systems: Connected and turned on. 180L LN2 dewar scales: Spectro 183 lbs, 22.2 psi ---=== SOFTWARE USED ===--- IOP/SOP: v4_40_0 Watcher: v2_36_0 MCP: v6_6_5 TPM: tpm_v3_5_0 AstroDa: v15_13_1 TCC: 337200 packets sent successfully sdssProcedures: v3_02 --TestActors --- 2010-04-21 01:51:46.551543 alerts ping OK alerts status OK boss ping OK boss status OK gcamera ping OK gcamera status OK guider ping OK guider status OK hub status OK mcp ping OK msg just testing OK perms status OK platedb ping OK platedb status OK sop ping OK sop status OK tcc show status OK tcc show time OK keys getFor=hub version OK loaded cart=10 pl=3818 side=A MCP instr 10 -----STUI software----- STUI ------- 0.5.2 2010-03-19 hub --------- Tag: sdss3_v1_1_3 boss -------- v2_2_2 specMech-- 3.0.1 guider -------v1_0_20e gcamera --- v1_0_6 MCP ------- v6_6_5 alerts ------- v1_0_3 platedb ----v1_0_3 tcc ---------- ? ---=== MIRROR NUMBERS ===--- PRIMARY: -------- Scale: 1.000000 MIGS TONIGHT NOMINAL Axial A -0.7000 -0.6940 Axial B -0.0300 -0.0410 Axial C -0.3760 -0.3710 Trans D 11.6060 11.6170 Lateral E 10.3759 10.3505 Lateral F 11.9507 11.9253 GALILS Commanded: 9900. 400. 5850. 1200. 2950. 2750. Actual: 9917. 401. 5832. 1205. 2954. 2757. SETMIR VALUES PriDesOrient: 0.00 -3.30 5.10 278.08 178.06 PriOrient: 0.00 -3.04 5.26 277.70 178.07 SECONDARY: ---------- Focus: 0.00 Air Temp.: 9.4 Alt.: 30.340746 MIGS TONIGHT NOMINAL Axial A 18.6100 18.6150 Axial B 15.6420 15.6120 Axial C 13.8280 13.8170 Trans D -11.7790 -11.7780 GALILS Commanded: 1597709. 1566200. 1588121. -7600. -12400. Actual: 1597721. 1566188. 1588095. -7597. -12380. SETMIR VALUES SecDesOrient: 1257.00 -4.00 -9.00 10.00 234.42 SecOrient: 1257.01 -4.01 -8.99 10.19 234.70 ---=== PROBLEMS IN DETAIL ===---